Press the (2) key and the zone(s) that activated Service Light “ON” – Pressing * 2 displays LED 2. Only the Hills Reliance 8, Reliance 12, and Reliance 128 can be zone doubled.Īny device connected to the data terminal on the Hills Reliance system can cause an You are trying to zone double a NX4 panel (not supported). #Networx alarm instant light code#Expander that can indicate low battery conditions: NX320 power supply.Īn expansion device connected to the Hills Reliance system has a tamper activated.Ĭheck the tamper contacts on the expansion devices connected.Įxpanders that can indicate box tamper: Code pads, Hardwire zone expanders andĬode pads are not number correctly (see * 94 code pad program).Įxpander connected is not seen by system. Arm and Disarm system to clear box tamper condition.Īn expander connected to the system has a short circuit on the Aux output.Įxpander that can report this condition are power supply (NX320).Īn expansion device connected to the Hills Reliance system has a Low BatteryĬondition. The box tamper pins are open circuit or activated. Output to disable Siren Trouble Monitoring. IfĪ horn speaker is not connected to the panel place a 3K3 resistor across the Bell The Hills Reliance control panel monitors the siren output for faults and tampering. The Horn Speaker is open / short circuit or not connected. Note if a severe short circuit is present it may exceed the protection available and Reliance 128 power will be restored when the thermistor resets (fuseless design). On the Reliance 8 and 12 power will be restored on fixing the condition. Screamer you must put the panel into alarm once the fault has been removed to Smoke Pwr will fix the over current condition. Press the (1) key and observe which LED comes on to indicate one of the following:Ī partial short-circuit on the Aux Pwr, Smoke power, Horn Speaker, Strobe or Service Light “ON” – Pressing * 2 displays LED 1. My Service Light is On Problem Solving Hills Reliance and DAS NX Alarm Panels Note if testing reporting, master code does not send open/closing reports by default (see Feature 2) Common Tasks when using DAS NX / Hills Reliance alarm panels.ĭefault Reliance / NX Installer code: 9713Įnter Installer mode: *8 -> Installer Code -> 0# What resistors do DAS NX / Hills Reliance Alarm Panels use? Exit Program Mode Press Exit, Exit, wait 12 secondsĢ2. Auto Test Control 32# (see Feature 32 for details)Ģ1. Medical Alarm Sounder “ON” 24# 7* (enable code pad beeping)Ģ0. #Networx alarm instant light manual#System Options 22# 7*7* # (for siren on tamper and manual communicator test enable)ġ9. #Networx alarm instant light download#Download Control (Remote Access) 14# 1* (to enable two call AMD)ġ6. Download Access Code 12# n*n*n*n*n*n*n*n*ġ4. Report Event Summary 9# 3 7 *# (for open/close, tamper/restore)ġ3. Communication Format 6# 1* (1 for CID, or 3 for Domestic Dial)ġ0. Soft Default Panel 910#, Exit, Exit,, wait 12 seconds 4. Hard Default Panel Unplug battery & remove power, turn on power, Enter 971300 within 10 seconds,ģ. This is not a substitute for reading the manualġ. Quick Start Guide Short form programming sheet for a monitored system Programming covers NX4, NX8, NX12, NX16, R8, R12, R128 versions of the alarm panel. This page is dedicated for all DAS NetworX and Hills Reliance alarm panels.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |